Interlogix TX-8300-01-1 Instrukcja Użytkownika Pobierz pdf (Strona 1)

1 of 3

P/N 466-2358 • REV C • ISS 26FEB13

Description

The DesignLine Tri-Zone Sensor provides the following

features:

Tri-zone sensing. Protects any three zones in close proximity

to each other. Reduces the labor and expense of multiple

sensors to protect multiple zones.

Garage door protection. Protects garage doors with tilt

sensing capability. Reports faults and restores based on the

position of the garage door (no magnet is needed).

Low battery LED indicator. Indicates a low battery condition

by flashing the sensor cover LED every 5 seconds.

Tamper switch protection. Provides a tamper switch that

indicates if the sensor cover is removed.

Figure 1: Sensor components

N/C zone inputs

3 Com 2

1 2 3

Battery

Jumpers

Reed switch

(1 zone)

Tamper switch

Roller-ball

tilt switch

Sensor top

Sensor bottom

Note: You can use a maximum of 18 ft. (6 m) of 24 AWG wire

on each zone (2 and 3).

If possible, locate the sensor within 100 ft. (30 m) of the control

panel. Open-air range is 500 ft. (150 m); environment can

significantly reduce the range.

Programming

Note: Refer to your panel documentation for complete

programming information.

You can use the sensor jumpers to enable the sensor to

protect three separate areas and report as three separate

zones.

Jumper 1. Leave jumper 1 on as positioned by factory default

(do not remove).

Jumpers 2 and 3. Use the jumpers as indicated below.

For auto learn mode (default jumper settings):

J 2

J 3

Description

Sensor w ill learn in all three zones w hen you activate

the tamper sw itch.

For manual programming (learning):

J 2

J 3

Description

Off

Select the zone to learn by faulting the desired zone.

To use the internal reed sw itch or the tilt sw itch, zone

1 must be programmed (learned).

Zone 1 = Remove the magnet.

Zone 2 = Open zone 2 external contact (fault).

Zone 3 = Open zone 3 external contact (fault).

Note: Replace jumper 2 w hen the zones have been

programmed.

Note: For zone 1, you must select either the reed switch

(jumper 3 on) or the tilt switch (jumper 3 off).

Garage door protection

You can use the sensor to secure a garage door without

running wires or using a reed switch.

You must program (learn) the sensor before you mount it.

To mount the sensor in a garage door installation:

1. Set jumpers 2 and 3 for your application:

J 2

J 3

Description

Off

Tilt sw itch is on in instant mode (no delay).

TX-8300-01-1 DesignLine Tri-

Zone Sensor Installation Sheet

1 2 3

Podsumowanie treści

Strona 1 - TX-8300-01-1 DesignLine Tri

1 of 3 P/N 466-2358 • REV C • ISS 26FEB13 Description The DesignLine Tri-Zone Sensor provides the following features: Tri-zone sensing. Protects a

Strona 2 - Regulatory information

2 of 3 P/N 466-2358 • REV C • ISS 26FEB13 J 2 J 3 Description Off Off Tilt sw itch is on in 1-minute delay. 2. Mount the sensor to the top panel

Strona 3 - Contact information

P/N 466-2358 • REV C • ISS 26FEB13 3 of 3 FCC This device complies w ith part 15 of the FCC rules. Operation is subject to the follow ing conditio

Komentarze do niniejszej Instrukcji

Brak uwag

Interlogix TX-8300-01-1 Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Interlogix TX-8300-01-1. Interlogix TX-8300-01-1 User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Interlogix TX-8300-01-1 Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Interlogix TX-8300-01-1. Interlogix TX-8300-01-1 User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Interlogix TX-8300-01-1