Interlogix Monitor XL Hardware Guide Instrukcja Użytkownika Strona 16

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 66
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 15
12 Monitor ISM/xL™ Hardware Guide
22-0375 rev1.1
8 and 16 Input/Output Expansion Modules
1432
(+) 12V
Data A
Data B
312
1432
F1
1/2 AMP
P/N 342-3356
1432
312
312312
312 312 312 312
0V
COM
COM
COM
COM
COM
COM
COM
COM
I/P1
I/P2
I/P3
I/P4
I/P5
I/P6
I/P7
I/P8
I/P9
I/P10
I/P11
I/P12
I/P13
I/P14
I/P15
I/P16
O/P1
O/P2
Switched (+)
Switched (-)
(-)
(-)
(+) 12V
(+) 12V
(+) 12V
0V
Module Bus Aux Power
red
green
yellow
black
312 312 312
O/P3
O/P4
O/P5
O/P6
O/P7
O/P8
0V
0V
0V
Tamper Pins
LED 2
follows O/P1
Annunciator
output board
male plug.
TB14
TB9TB5TB1TB6TB2
TB10 TB11 TB12
TB7 TB3 TB8
TB4
TB13
16 Input (8 Output) Expander Module
16 Outputs with Annunciator Output Board
1432
Data A
Data B
1432
F1
1/2 AMP
P/N 342-3356
1432
312
312
312 312
COM
COM
COM
COM
I/P1
I/P2
I/P3
I/P4
I/P8
I/P7
I/P6
I/P5
(-)
(-)
(+) 12V
(+) 12V
(+) 12V
0V
Module Bus Aux Power
red
green
yellow
black
Tamper Pins
LED 2
follows O/P1
LED 1 Bus
communications
indicator
TB14
TB9TB1TB2
TB3
TB4
TB13
8 Input (2 Output) Expander Module
10 outputs with Annunciator Output Board
1432 1432
14321432
LED 9
LED 10
LED 11
LED 12
LED 13
LED 14
LED 15
LED 16
O/P9
TB1 TB2
0V
O/P10
0V
O/P11
0V
O/P12
0V
O/P13
O/P14
O/P15
O/P16
0V
0V
0V
0V
TB3TB4
Annunciator
Output Board
Outputs 3 - 8 do not exist.
LED 1 Bus
communications
indicator
identical
operation
Current rating = 25mA without
annunciator card. 60mA with
annunciator card and all LEDs on.
Current rating = 25mA without
annunciator card. 52mA with
annunciator card and all LEDs on.
5 digit serial number to
program in Module
Programming
5 digit serial
number to
program in Module
Programming
XXXXX
XXXXX
The Annunciator Output Board (P/N 650-2660) can be used on either Input / Output module.
When used on the 8 Input module, outputs 1 and 2 can be programmed but, in order to program outputs and
LEDs 9 – 16 on the annunciator card, outputs 3 – 8 must be skipped.
The 8 Input module must still be assigned 16 outputs in order to program outputs/LEDs 9 – 16 on the annunciator
card.
Outputs 1 and 2 are identical operation on both modules.
16 Inputs and 16 outputs are available on the 16 Input module using the annunciator card.
Refer to Installation Instructions P/N 22-0363 for
further information.
Przeglądanie stron 15
1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 65 66

Komentarze do niniejszej Instrukcji

Brak uwag