Interlogix NX-6V2 REV B Installation Manual Instrukcja Użytkownika Pobierz pdf

NX-6V2 Control Panel Installation Instructions

Introduction

This is the NX-6V2-Control Panel Installation Instructions.

Installations should only be done by trained professionals. Use

this document to install the system with default settings that

comply with UL requirements.

To install the keypad, other peripherals, and sensors, refer to

the documentation for those devices.

Installation

There are four slots for board insertions inside the metal

enclosure, two on the top and two on the bottom. These allow

the PC board to be positioned vertically (Figure 1

). When you

slide the board between the grooves of the slots, make sure

the terminal strip is toward the front opening (toward you) to

allow for the wire connections.

Note: Install the metal enclosure with the door opening from

the top to bottom.

Figure 1 Board Installation

NetworX keypad maximum wire run

Table 1 lists wire lengths for one keypad at the end of the wire.

When connecting more than one keypad to the end of the wire,

a higher gauge wire is required

Table 1: Maximum keypad wire run

Length in feet Wire gauge for NX-6v2 Wire gauge for NX320-E

250 24 22

500 20 18

1000 18 16

1500 16 14

2000 14 12

Terminal descriptions

Table 2 describes the panel terminals

Table 2: NX-6V2 Terminals

Terminal Description

R1 House telephone ring (grey).

R Telephone ring (red).

T Telephone tip (green).

T1 House telephone tip (brown).

EARTH Earth ground. Connect to a cold water pipe or a 6 to

10 ft. driven rod.

C AC input. Connect to a 16.5 V, 40 or 50 VA Class II

UL approved transformer.

Bell + and

Bell -

If used as a siren output (default), the speaker rating

should be 15 watt at 8 or 16 ohm, or 30/40 watt at 4,

8, or 16 ohms. If voltage ouput is selected in location

37, this output becomes voltage output, 12 VDC, 1

Amp maximum load. Note: A 3.3 kohm resistor may

be required across the bell terminals when a 12 VDC

siren is used. If no resistor is used, you may

experience voltage leakage into the siren, which will

cause these devices to output a small signal.

KP DATA Connect to the data terminal on the keypads and the

expanders. Maximum number of devices is 16

keypads plus 3 other de vices. See Maximum Wire

Run table.

KP COM Connect to the common terminal on the keypads and

the expanders.

KP POS Connect to the POS terminal on the keypads and the

expanders. Individually, this terminal is limited to 1

amp. Combined, this terminal and AUX PWR+ are

limited to 2 amps total current.

COM Common negative wire of powered devices such as

motion detectors and smoke detectors.

UXPWR + Connect positive wire of all powered devices except

smoke detectors and keypads. Individually, this

terminal is limited to 1 amp. Combined, this terminal

and KP POS are limited to 2 amps total current.

P/N 466-2338 • REV B • January 2011 1

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - Installation

NX-6V2 Control Panel Installation Instructions Introduction This is the NX-6V2-Control Panel Installation Instructions. Installations should only b

Strona 2 - Control panel programming

Abort annunciation This feature is not programmable in the panel. Flashing cancel LED goes off when disarming. Enabled Cancel annunciation Cancel

Strona 3

ZONE 7 Connect to one side of zone 6 loop. Connect the other side to com terminal. Open or short causes alarm. Only zone 6 can be used for a two-wire

Strona 4

3. Press  to store the newly entered data. The keypad advances to the next segment and displays its data. Repeat this procedure until the last segmen

Strona 5

a 0, the built-in communicator is disabled and the NX-6V2 functions as a local-only control. Table 4 communicator formats Data Format Description 0 L

Strona 6

Segment 2 1. Zone and box tamper and tamper restore. 2. Auxiliary power over current, ground fault, and restore for both. 3. Wireless sensor missin

Strona 7

14. Entry/exit delay 1 with group bypass A trip starts entry delay 1. This zone bypasses when the group bypass command is entered at the keypad. The l

Strona 8 - Specifications

• Total current draw from auxiliary power connections at terminal positions POS, AUX PWR, and SMOKE PWR must not exceed 400 mA. • Remote downloading

Strona 9 - ANSI/SIA CP-01 requirements

WARNING: Electrical codes will vary, depending on the country and city where the system is installed. It is the installers responsibility to ensure th

Strona 10

Regulatory information Contact information FCC compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following

Komentarze do niniejszej Instrukcji

Brak uwag

Interlogix NX-6V2 REV B Installation Manual Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Panel sterowania Interlogix NX-6V2 REV B Installation Manual. Interlogix NX-6V2 REV B Installation Manual User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Panel sterowania Interlogix NX-6V2 REV B Installation Manual