Interlogix NX-4 Instrukcja Użytkownika Strona 31
- Strona / 44
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
NX-4 Control
Page 29
LOC
PG
DESCRIPTION
DEFAULT
DATA
KEYPAD SOUNDER CONTROL
Segment #1 (Circle numbers to program)
39 18
1
2
3
4
5
6
7
8
Reserved.
Reserved.
Keypad sounds upon AC Power Failure.
Keypad sounds upon Low Battery Detection.
Keypad sounds during Cross Zone Trip Time.
Keypad sounds for Tamper Alarm.
Reserved.
Keypad sounds for expander trouble (required for UL).
SYSTEM TIMERS
Segment #1 Dynamic Battery Test duration (0-255 min.) 0 _
Segment #2 AC Failure report delay (0-255 minutes) 5 _
Segment #3 Power Up Delay (0-60 seconds) 60 _
Segment #4 Siren Time (1-255 minutes) 8 _
Segment #5 Reserved 0 _
Segment #6 Cross Zone Time (0-255 minutes) 5 _
Segment #7 Chime Time in 50 mS increments (0-255) 3 _
Segment #8 Dialer delay (15-255 seconds) 30 _
Segment #9 Fire Alarm Verification Time (120-255 sec.) 0 _
40
18
Segment #10 Listen-In Time (0-255 seconds) 0 _
USER CODE REQUIREMENTS
Segment #1 (Circle numbers to program)
41
19
1
2
3
4
5-8
Enables six-digit code option. All arm/disarm/Go To Program codes require six digits
Requires valid user code entry for [r]-[9]-[8] and [r]-[9]-[9] functions to work.
Enables Auto Cancel/Abort.
Enables Walk Test mode.
Reserved.
42
19
GO TO PROGRAM CODE
9-7-1-3-0-0
_ _ _ _ _ _
GO TO PROGRAM CODE AND AUTHORIZATION
Segment #1 (Circle numbers to program)
43 19
1
2
3
4
5
6
7
8
Reserved.
Enables "Go To Program Code" as an arm only code.
Enables "Go To Program Code" as an arm only after closing.
Enables "Go To Program Code" as a master arm/disarm code (can change user codes)
Enables "Go To Program Code" as an arm/disarm code.
Enables "Go To Program Code" to bypass zones.
Enables "Go To Program Code" opening and closing reports.
Reserved.
44 19 DURESS CODE 15-15-15-15-15-15 _ _ _ _ _ _
46 19 AUXILIARY OUTPUTS 1 & 2 SPECIAL TIMING
Segments 1 2
Auxiliary output timed in minutes.
Auxiliary output to latch.
Auxiliary output to stop timing upon user code entry.
Auxiliary output to activate only between closing and opening time.
Auxiliary output to activate only between opening and closing time.
Invert auxiliary output (0 volts going to 12 volts when activated).
Reserved
Reserved
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
- NetworX Series 1
- NX-4 Control Panel 1
- NetworX NX-4 3
- Control/Communicator 3
- Installation Manual 3
- BOARD INSTALLATION 4
- PROGRAMMING THE LED KEYPADS 10
- PROGRAMMING DATA 12
- PROGRAMMING EXAMPLE – 13
- FIGURE 2 13
- (Feature Selection Data) 13
- LOADING FACTORY DEFAULTS 14
- FORMAT SELECTIONS 15
- Page 14 16
- Page 16 18
- (Note: Must be disabled 19
- Page 18 20
- Page 20 22
- Page 22 24
- Page 24 26
- PROGRAMMING WORKSHEETS 28
- Page 28 30
- Page 30 32
- Page 32 34
- Page 34 36
- KEYPAD MAXIMUM WIRE RUN 37
- NX-4 Control 38
- WIRING DIAGRAM 38
- TERMINAL DESCRIPTIONS 39
- Page 40 42
- SPECIFICATIONS 44
Powiązane produkty i podręczniki dla Panel sterowania Interlogix NX-4
(18 strony)
(21 strony)Samsung NV73J7740RS manuály
Uživatelské manuály a uživatelské příručky pro Pece Samsung NV73J7740RS.
Poskytujeme 1 manuály pdf Samsung NV73J7740RS ke stažení zdarma podle typů dokumentů: Instalační manuál
Komentarze do niniejszej Instrukcji