Interlogix NX-4V2 Installation Guide Instrukcja Użytkownika Pobierz pdf (Strona 1)

NX-4V2 Control Panel Installation Instructions

Introduction

This is the NX-4V2-Control Panel Installation Instructions.

Installations should only be done by trained professionals. Use

this document to install the system with default settings that

comply with UL requirements.

To install the keypad, other peripherals, and sensors, refer to

the documentation for those devices.

Installation

There are four slots for board insertions inside the metal

enclosure, two on the top and two on the bottom. These allow

the PC board to be positioned vertically (Figure 1 below).

hen you slide the board between the grooves of the slots,

make sure the terminal strip is toward the front opening

(toward you) to allow for the wire connections.

Note: Install the metal enclosure with the door opening from

the top to bottom.

Figure 1: Board installation

NetworX keypad maximum wire run

Table 1 below lists wire lengths for one keypad at the end of

the wire. When connecting more than one keypad to the end of

the wire, a higher gauge wire is required

Table 1: Maximum keypad wire run

Length in feet Wire gauge for NX-

4V2

Wire gauge for NX320-

250 24 22

500 20 18

1000 18 16

1500 16 14

2500 14 12

Terminal descriptions

Table 2 below describes the panel terminals.

Table 2: NX-4V2 terminals

Terminal Description

R1 House telephone ring (grey wire on the standard RJ-31X

cord).

R Telephone ring (red wire on the standard RJ-31X cord).

T Telephone tip (green wire on the standard RJ-31X cord).

T1 House telephone tip (brown wire on the standard RJ-31X

cord).

AC AC input. Connect to a 16.5 V 40 or 50 VA Class ll UL

approved transformer.

EARTH Earth ground. Connect to a cold water pipe or a 6 to 10 ft.

driven rod.

AUX1 Connect negative lead of low current device [relay, LED

(install 1 kohmresistor in series with LED), etc.]. Connect

positive lead of device to COM. Current is limited to 50

mA when output is negative, and 250 µA when output is

positive.

SIREN If used as a siren output (default), the speaker rating is 15

watt at 8 or 16 ohms, or 30/40 watt at 4, 8, or 16 ohms. If

voltage output is selected in location 37, this output

becomes voltage output, 12 V, 1 A maximum load. A 3.3

kohmresistor is required across the bell terminals when a

12 V siren is used. If no resistor is used, you may

experience voltage leakage into the siren, which causes

these devices to output a small signal.

COM Connect negative wire of powered devices, such as

motion detectors and smoke detectors.

P/N 466-2337 • REV B • January 2011 1

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - Installation

NX-4V2 Control Panel Installation Instructions Introduction This is the NX-4V2-Control Panel Installation Instructions. Installations should only be

Strona 2 - Control panel programming

CP-O1 feature description Feature description as shown in manual Program location Seg/opt Default CP-01required setting Exit time and progress annun

Strona 3 - Q ick start program

Terminal Description SMOKE+ Smoke detector power 12 V, 1.5 A maximum. AUX2 t t is negative, and 250 µA when output is Connect negative lead of low c

Strona 4

key. You can find other module entry numbers in the module illumprog 1. location is a valid location, nt of the location is 2. ing xt segment and di

Strona 5 - Location 1

• To program tone dialing, enter 15 in the segment whtone dialing begins. ere • If the entire number is tone dialing, enter 15 in the first segment.

Strona 6 - Underwriters lab

• Program a 1 in segment 2 to cause the NX-4V2 to stop ake , the next two attempts to Location 4 has two segments of feature selection data. Use to s

Strona 7

Table 5: Zone types Zone type Description Zone type Description 1. Day zone This zone is instant when the system is armed; trouble zone when the sy

Strona 8 - Specifications

UL365 Police station connected burglar alarms UL609, CAN/ULC-S303- Mercantile, police station connect with -C M91 basic line security requires NX-003

Strona 9 - Contact information

protected area, is acceptable, provided it is rated for outsidservice and alarm conditions are transmitted to: a) The dispatch location of the law enf

Strona 10

NX-4V2 Control Panel Installation Instructions 9 e electable 50 mS or 500 mS Loop respons SOperating temperature to 49°C) 32 to 120°F (0 LED keypad

Komentarze do niniejszej Instrukcji

Brak uwag

Interlogix NX-4V2 Installation Guide Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Panel sterowania Interlogix NX-4V2 Installation Guide. Interlogix NX-4V2 Installation Guide User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Interlogix NX-4V2 Installation Guide Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Panel sterowania Interlogix NX-4V2 Installation Guide. Interlogix NX-4V2 Installation Guide User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Panel sterowania Interlogix NX-4V2 Installation Guide